Search
Categories
Airframe Parts
Avionics
Batteries
Books & Videos
Charts
Composite Materials
Covering Supplies
Electrical
ELTs
Engine Parts
Flight Training
Flight Planning
Gifts
GPS
Hardware
Headsets
Instruments
Landing Gear
Metals & Plastics
Pilot Supplies
Radios
Tires & Tubes
Tools
Wood Products
Kits & Plans
FBO Supplies
Liqui Moly AERO
Catalogs
Avionics
Batteries
Books & Videos
Charts
Composite Materials
Covering Supplies
Electrical
ELTs
Engine Parts
Flight Training
Flight Planning
Gifts
GPS
Hardware
Headsets
Instruments
Landing Gear
Metals & Plastics
Pilot Supplies
Radios
Tires & Tubes
Tools
Wood Products
Kits & Plans
FBO Supplies
Liqui Moly AERO
Catalogs
Katalog nur für gewerbliche Kunden. Alle Preise zzgl. MwSt.[Preise inklusive MwSt zeigen]
Shipping country set to GermanyAlcohol Resistant Gas Tank Sealer Gallon
| Part number: | 09-02566 |
Hazardous Materials!
Description:
This is impervious to all fuel types. Over 2,000,000 sold to date. It is the best way to repair and restore your fuel tank. Simple application, includes extensive application information and product information sheet. Will seal pinhole leaks and prevent rusting. 1 Pint will seal a 10-12 gallon tank. Good for all fuel types. Works well with all metal and fiberglass tanks.
Note: For Experimental Aircraft Only!
Q+A
I'm looking at sealing a very slight seepage at the sump drain flange on my RV-4- Aluminum tank with aluminum sump valve flange- and I use motor gas w/ethanol in my plane. I am looking at something with low viscosity to flow into the area that is leaking, and perhaps setting up a slight vacuum with a toilet punger to draw the sealant into the seepage.(this is aerospace engineering, after all). Does this product have a fairly low viscosity, or can it be thinned a bit with, say, MEK?
Per the vendor, if it is used shortly after purchase, part number 09-03477 should not need anything to thin out the product. Make sure it is well mixed and it should be fine without any additional products.
Will this also adhere to plastic gas tank such as on a snowmachine? It would also have to be resistant to extreme temperatures such as -40 to +180 approx.
This sealer is only recommended for metal or fiberglass fuel tanks.
You say this works in fiberglass tanks, would it work in fiberglass foam epoxy tanks like the Long EZ has?
This is a tricky question. Yes it should work, but there are no specific tests done with any specific epoxy or resin system used to make a fiberglass tank. As long as the tank is cleaned and prepped properly, it should work just fine.
Can this be poured into wing tanks and sloshed around to seal leaks?
Per out product support manager: it is a sloshing material that will fill small pin hole leaks and seal the inner tank. It can be poured in and sloshed around in a fuel tank.
What is the shelf life before this alcohol resistant gas tank sealer must be used?
Per the supplier: this product has a 2 year shelf life that starts once it is opened.
What is needed to prepare the inner tank surface before using the Alcohol resistant gas tank sealer?
Per the manufacturer: The entire interior of the tank must be dry. If only one small area of the tank is not dry or has foreign matter that may keep the sealer from adhering, the sealer will not stick to those areas and could come loose and float around in your tank and eventually come through the fuel pick up tube and clog the fuel pump and carburetor. The solvent for this sealer is methyl ethyl ketone (mek). Before introducing any additives to fuel tank after sealer has been installed, be sure that the product you introduce does not contain (mek). (mek) can soften and loosen the sealer which in turn can clog your fuel lines, carburetor, etc. Avoid using "gumout" or similar products which have been known to use (mek).
Is the alcohol resistant tank sealer (pn 09-03477) comparable with the pro-seal ps 890 class b (pn 09-38560)?
The 09-03477 is a sloshing sealer that gets poured in a fuel tank and the tank rotated so the material gets on all parts of the tank. The 09-38560 is a much thicker material and requires a brush to spread the material.
| Unit | EA |
| Hazardous | Yes |
| Oversize | No |
| Weight | 3.716 kg |
This part is included in the following categories:
Log in
Shopping cart is empty
Subtotal excl. VAT:0 EUR
Latest News
 | Call us at +49 7634 9057700 from 08:00 to 13:00 CET |
